STEYR 8120 Turbo SK1 v 2.0 [MP]

STEYR 8120 Turbo SK1 v 1.0

STEYR 8120 Turbo SK1 v 1.0

STEYR 8120 Turbo SK1 v 1.0

Hello, so since the 4 cylinder SK1 model is a bit too small for some activities, such as bale presses ect, we have brought the 6 cylinder, 8120 SK1 to life in just 2 days 🙂 The Sk1 model from the previous LS version was reworked , (Roof cut out, wider Kotis rear mounted, exhaust cut and exchanged, …)


Construction period: 1978 – 1984

Weight: 4400kg (4WD version)

Engine: STEYR 611.86, 6 cylinders with a displacement of 5.2l

Gearbox: gives meherere, we have the 30-speed Deutz TW90 with 15v / 5r gears, and once the gearbox with the retrofit set (18v / 6r speed -> 40 kmh)

Tank load: 122l

Power: 100 HP according to -DIN specification

Engine history: Front wheel drive (4WD)

Cabine: Steyr Super comfort First generation cabin (SK1)

A great THANKS goes to forbidden-mods for sharing to the Siloking Terminal.


from the outside:

Front fender on / off button R (only with 4WD, with 2WD are fixed)

turn left door on / off button R

open / close left button R

Snow chains (front / rear) on / off button R (with 4WD, with 2WD only rear)

Shop configurations:

Coupling Products:

Standard / front spoiler: (atacher joint installed)

Front hydraulics + front spoiler (Dynamic Hose ready)

Front loader attached:

(Dynamic Hose ready)

with front protection

without front protection

Engine version:

100 hp without “Turbo” lettering on the bonnet:

Exhaust + flap BJ 78: (SK1 roof) 30-speed gearbox (15v / 5-speed)

Low noise exhaust BJ 80: (SK1 roof) 30-speed gearbox (15v / 5-speed)

100 hp with “Turbo” lettering on the bonnet:

Exhaust + flap BJ 84: (SK2 roof, roof light front + roof hatch) 40-speed gearbox (18v / 6r speed)

Low-noise exhaust BJ 84: (SK2 roof, roof light front + roof hatch) 40-speed gearbox (18v / 6-speed)

Wheel setup:


Original: front: 340/85 / R24 rear: 460/85 / R34


Original: front: from 8080 SK1 rear: 460/85 / R34


Design Confi 1:

round arbeisscheini Koti in the back left

RUL middle

RUL rear

round Arbeisscheini Koti rear left + RUL center

round Arbeisscheini Koti rear left + RUL behind

Design Confi 2:

VA (front axle) protection

VA + floor protection, intended for a forestry set (chainsaw + benzine tank is visible)

Other functions:

IC control:

Rear windows, side windows and left door (including door closing sound) for opening / closing

FH-Unterlenker, co-driver’s footrest and sun visor fold in / out

windshield wipers

cabin light

Siloking Terminal fade-out / fade-out

Animated / Illuminated:

Tacho, tank and temperature display as well as pressure air display

Blinker / warning indicator (including turn signal (from a Steyr 8130a SK2))

Blinker / warning light indicator works as in real:

Tractor alone = 1 beam flashes

Tractor + 1 trailer = 2 lights flashing

Tractor + 2 trailers = 3 lights flashing

license plate light

Charge indicator light integrated (battery lit jz at engine start)

“provisional” animated pedals; Accelerator pedal, brake pedal + clutch: IMPORTANT! Drive control with active reversing circuit (green arrow must be visible -> direction change) otherwise the pedal animation does not fit. (Select tractor)

at selected tractor without attached trailers / equipment: animated rear hydraulic + lever (right in the tractor) TASTE V,

animated lever for the PTO coupling (on the left in the tractor) BUTTON B is a small tool for moving around the cabin, this is a pure look for the levers to be attached to the attached devices, you need a suitable script, we guess. 🙂 With trailers attached you can lift the HH (rear hydraulics) (tractor must be selected) and the lever moves.

The lever for the ZWK (Zapfwellenkupplung) can be switched on / off at any time (tractor must be selected), it has no function, it is purely optical.


Textures reworked

Model has been revised

Chain saw installed as decoration

genuine tire moldings were used


Indoorsound (reacts to open windows or doors)

Working light front Button NUM 5 (only for 8120 Turbo SK1, 40 speed version)

Working light rear button NUM 6

swing axle

Behrahrerskript installed

Low beam + high beam + working light somewhat yellowish as well as in real life

Required / Recommended Mods:


Drive Control

Front loader for medium tractors

Gearbox Add On


Modell: Urmodell: MB3D Modelling, Umbau/LS17 ready: STEYR Modding Team,, Siloking Terminal: forbidden-mods/Bremi456
Textur: MB3D Modelling, STEYR Modding Team, Siloking Terminal: forbidden-mods/Bremi456
Script: Giants Software, Fruktor, Rival (RivalBomb), Manuel Leitner, PeterJ – euroDZN, Sven777b, Modelleicher, Alex2009, BM-Modding (Dynamic Hose Skript)
Idee / Konzept: STEYR Modding Team
Tester: STEYR Modding Team

Sounds: STEYR Modding Team

Schneeketten: CebuljCek Modding

5/5 - (1 vote)

Leave a Reply

Your email address will not be published. Required fields are marked *